Click Here

 

How do you actually feel about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Mounting a bath tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a brand-new one is likewise a reasonably challenging task. If the old tub is conveniently accessible, the project can relocate easily; if you need to open a wall surface to get rid of the old tub and also position the new bathtub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly require a helper to move out the old tub as well as set in the new one. Make certain you have actually certified on your own for the task and are comfortable trying it. Rather than working with a specialist to take over a halfway-completed task, it is far better to think about utilizing one before you begin. Chances are you might require a specialist plumber to make tube connections.
This post will help you mount a new bath tub in your bathroom if you have currently acquired a brand-new bathtub and also don't need to transform the setup of your previous supply of water pipelines.
Your tools and also product checklist ought to comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Preparing for the Setup

Firstly, the supporting framework supplied with the bathroom ought to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to prevent pressure on the tub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you make use of all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its final placement.

 

 

Removing Old Taps

If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the supply of water. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly bothersome due to the limited gain access to that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a fabric all set for the remaining water that will come from the pipes. When the supply pipes have been removed, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this process. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing compound.
Prior to going on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Installing the Tub

Making use of both wood boards under its feet, put the bathtub in the required setting. The wooden boards are useful in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bath tub till the spirit level checks out level.
To mount taps, fit the bottom of the furthest adaptable tap port to the proper supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water and also check all joints and brand-new pipework for leaks as well as tighten them if required. Load the tub as well as additionally examine the overflow outlet and also the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait up until the tub has been utilized at the very least when as this will resolve it right into its final placement.

 

 

Fitting New Taps

If the tails of the new taps are plastic, after that you will certainly require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making certain that the washers are in area in between the tap as well as the sink. Secure the faucet in position with the maker offered backnut. As soon as the faucet is safely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The previous type should be linked to the tap finishes first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bath tub

In the area where the bathroom meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to break a stiff seal, creating the water to penetrate the wall surface in between the bath and the tiling, resulting in difficulties with moisture and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly load the tub with water prior to sealing, to allow for the movement experienced when the tub remains in usage. The sealer can split fairly early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or water-proof adhesive and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As an enthusiastic reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I imagined sharing that excerpt was beneficial. So long as you appreciated our article if you please be sure to pass it around. Many thanks for your time invested reading it.

Need Help? Hire Us Now!